Rent or buy the by ETS-Lindgren (EMCO) in the test equipment industry at MODEL DOUBLE-RIDGED WAVEGUIDE HORN . EMC Test Systems, L.P. , hereinafter referred to as the Seller, warrants that standard EMCO products. Buy Emco MHz to 2 GHz Double Ridged Waveguide Horn Antenna and other Antennas from Test Equipment Center.
|Published (Last):||23 October 2015|
|PDF File Size:||1.7 Mb|
|ePub File Size:||19.42 Mb|
|Price:||Free* [*Free Regsitration Required]|
The waveguide features industry-standard flange mounts.
Increased Power Dissipation While the coaxial feed allows power input of up to W Model02, emchigher power input is possible by removing the detachable feed and direct mounting the flange to an amplifier waveguide port. Although large in size, To maximize performance, Type N connectors are used on Models andand Type K connectors are used on Model The mounting brackets for Models and are adjust- able for changing polarization of the antenna. Complain wrong Brand wrong Model emmco readable.
Antenna factors are constant throughout the entire operating frequency range. As a set, these linearly polarized broadband antennas have an average VSWR of less than 1. Quality Construction Double-ridged waveguide antennas are constructed of light- weight corrosion-resistant aluminum e,co fiberglass, providing years of trouble-free indoor and outdoor service.
When additional power input levels are required, the coaxial feeds are easily removed from the waveguides.
Diagonal dual polarized horn | Atec EMCO User Manual | Page 7 / 14
Constant Antenna Factor Over Frequency. This antenna is small and portable with a length of Type K female connectors are used above 18 GHz. A Type K female connector is used for increased performance at high frequencies. All models have uniform gain throughout their frequency span, providing efficient performance characteristics and directionality. All models in the series are linearly polarized, have medium gain, optimum half power beamwidth equal in both horizontal and vertical planesand low VSWR.
The antenna is also useful for receiving low-level signals where high gain characteristics are needed. Octave horns are essentially the same as our standard gain horns, except that they are equipped with waveguide-to-coaxial feeds which are matched in frequency to common octave bandwidth amplifier ranges.
The Model has a length of only While the coaxial feed allows power input of up to W Model02, 03higher power input is possible by removing the detachable feed and direct mounting the flange to an amplifier waveguide port. Optimal Beamwidth The 3 dB beamwidth in both polarization planes is very nearly equal at approximately 30 degrees.
Models and 10 are electroformed using copper deposition at the rate of 0. Complete with Feed, Waveguide, and Mount. A mounting bracket is included with all models and allows either vertical or horizontal polarization measure- ments. Complete with Feed, Waveguide, and Mount Unlike most antennas of this type, EMCO supplies a complete unit with detachable coax-to-waveguide feed and mounting brackets for both horizontal and vertical polarization.
Used ETS-Lindgren / ETS / EMCO for sale by Bell Electronics NW, Inc. |
Precision Type N female connectors are used for antennas operating below 18 GHz. Power Handling Model can handle W peak and W continuously. A Type N female connector is used for increased power handling. The Model is an extremely small antenna, offering portability and increased efficiency.
Standard gain & octave horn – Atec EMCO-3106-3115-3116 User Manual
These antennas are specifically designed for EMI measurements, but can also be used for Emvo, antenna gain and pattern measurement, surveillance, and other applications.
Models and 08 are investment cast using an alumi- num alloy.
Complain wrong Brand wrong Model 1306 readable. Model can handle W peak and W continuously. The feed system uses a Precision Type N female connector so the antenna can handle considerable power with low losses above 12 GHz.
Industry standard flanges mount directly to amplifiers equipped with waveguide ports. Double-ridged waveguide antennas are constructed of light- weight corrosion-resistant aluminum and fiberglass, providing years of trouble-free indoor and outdoor service. The 3 dB beamwidth in both polarization planes is very nearly equal at approximately 30 degrees.
Diagonal dual polarized horn – Atec EMCO-3106-3115-3116 User Manual
Unlike most antennas of this type, EMCO supplies a complete unit with detachable coax-to-waveguide feed and mounting brackets ekco both horizontal and vertical polarization. Precision manufacturing contributes to the predictable performance of these antennas. It is especially effective for generating high electromagnetic fields with relatively low power input.
Models through 06 are welded using precise tooling and aluminum sheet metal.
Power Handling up to 1.