Categories Parts fuel Parts Hirobo Shuttle Sceadu SCEADU MANUAL Ask question. Description. SCEADU MANUAL. Browse this category: Shuttle Sceadu . Categories Parts fuel Parts Hirobo Sceadu Evolution SCEADU SWM INSTRUCTION MANUAL MANUAL. Browse this category: Sceadu Evolution. Beyond Sceadu!! SDX 50HPM kit. This swashplate accepts 90°HPM,. °SWM, and °SWM linkage for all Hirobo 50/90 size models.

Author: Mazukinos Duzragore
Country: Mongolia
Language: English (Spanish)
Genre: Travel
Published (Last): 15 March 2016
Pages: 191
PDF File Size: 12.85 Mb
ePub File Size: 3.87 Mb
ISBN: 643-4-93870-946-6
Downloads: 77158
Price: Free* [*Free Regsitration Required]
Uploader: Samubar

Normal Radio Switch positions are all switches up front panel and back top of radio. Each Tail Blade Holder uses a single thrust bearing and radial bearing for exact rotational movement.

I got mm sticking out of either side. Correct frame holes to use in step 4. The helicopter was further developed hiroboo into a 90 size version. Canopy and Decals ready to apply. Quick UK Pushrod Tool. The Proto-Z is a Blast of micro-sized fun! We also highly recommend that an experienced rc helicopter pilot checks out your model before its first flight and be with you to teach you how to fly your model.

One of the really nice things about the EVO is that it’s highly tunable in its stock configuration. Thrust bearings are standard for smooth collective changes through the entire pitch range especially under the demanding loads of radical 3D flight.

hirobo sceadu evo 30 combo set up sheet for use with mrc |

To put the decals on I used a small bowl and put 5 or 6 drops of dishwashing liquid in and filled it with warm water. Return to Magazine Homepage.

Terms of Service Privacy Policy. I always like to have a second set of eyes go over my helicopters before a maiden flight or after a major scaedu. Repeat the process on the other grip and you should have both sides done. The very same problem occurred on the next flight.

Don’t forget to locktite the screws! Some right trim was expected, a bit of right cyclic is required to counteract translating tendency; the tendency of the helicopter to slide to the left in a hover from the tail rotor blowing the helicopter sideways. Start by making up the push rods; the ssceadu gives shoulder to shoulder measurement of 14mm, I prefer ball center sceau ball center measurements so I can use my push rod tool for my calipers but this works just as well. Once throttle hold was set, I activated throttle cut to make sure it would kill the engine.

  ACLM HANDBOOK PDF

This set up sheet is a supplement and not a replacement for the manual or having an experienced helicopter modeler inspect your model before its first flight. It used a small drill press vice to set the pin in to the radius arm and mixing lever as maanual was a very tight fit and wanted to get even pressure.

HPM being the originally mechanical pitch version with a rocking cradle and SWM; this was the upcoming ccpm control system that required a transmitter with electronic swashplate servo mixing to give both cyclic and pitch functions. Made of durable impact resistant polypropylene. Take a thin file or emery board and take a small bit of material out of the channel until you can spin the guide freely with a very light touch of your finger.

New larger pulleys allow stronger belt contact under the severest of conditions. Accepts 12mm root Main blades with 4mm bolt hole.

Hirobo Shuttle Sceadu Evolution Manuals

Any time that I have had a question and have emailed or called Jeff, the response has always been prompt and accurate. Again available in both ’30’ and ’50’ sizes though as before, predominantly bought as the ’50’ variant. Oil and slide the washout base on to the shaft and snap the arms on to two inner balls on the swash plate. When starting you model, make sure Switch B is up, throttle trim is in the middle, and you have a firm hold of the rotor head to keep it from spinning after starting your model.

Hirobo has stepped up and given the EVO sceacu point tail rotor pitch control, an excellent design. Put the balls on the 8mm bolts and screw the balls into the outer holes on the mixing arms. They are adjustable and easily removable should you need to hifobo the tail boom.

  ANATOLE BROYARD INTOXICATED BY MY ILLNESS PDF

If you’ve built a helicopter or two, the EVO should present no problems. Main Frame is capable of handling standard collective pitch controls or Hirobo’s SWM swash scceadu deg. Aligning servo arm sveadu throttle arm.

If your engine starts running rough after running well for a period of time, do not adjust the needle valves immediately. Check the orientation of the belt. Sceasu wish they had taken this one step further by using hex head screws and nyloc nuts for the frame assembly but they can be ordered in packages of ten from your favorite retailer. Again available in both ’30’ and ’50’ sizes though as before, predominantly bought as the ’50’ variant. Floating axle design with wide dampeners for extra support of the Feathering spindle.

The EVO did every maneuver we could throw at it. RCGF, a Chinese manufacturer of gasoline engines, designs and manufactures engines specifically for mannual RC aircraft market. On this page you will find helpful mxnual photos.

Hirobo Shuttle Sceadu Evolution Instruction Manual Page 48

New drive train layout puts engine in front of main shaft for better overall CG balancing and allowing the gear reduction for the tail gearbox to happen hiroboo the main gear instead of a pulley arrangement.

Now remove the engine mount bolts one by one and locktite them and reinstall and tighten them. OS 50 Hyper Gyro used: Great for aerobatic autos. Make note of the diagram in the manual when mounting the tail rotor servo, the servo goes in the lowest set of holes. Kit comes with carbon main and tail blades.

Last modified: June 9, 2020